Full size Paper dress form

several people have asked me if my half-scale paper dress form pattern can be enlarged to make a full scale dress form, and I wasn’t sure how well that would work, so I made a decision to try it.

I re-made the pdf patterns at twice the size so I could print them on 8 1/2″ x 11″ paper. It came out to 56 pages. Yikes. but each original pattern piece fit on a single piece of paper, so I only had to tape together 4 sheets at a time, which wasn’t that bad. If you’ve gotten the paper dress form pattern on Craftsy or Etsy, I will send you the full-scale pattern if you ask me for it. I also have available a pdf that will print on three sheets on a large format printer (copy shop version) in addition to the 56 page version.

I glued each pattern piece onto poster board, using a total of 5 sheets of poster board. I had some problems. Poster board is about the ideal thickness for this project, but it is made from layers of different types of paper, and it wrinkles when it gets wet. I must have used spray glue, but I didn’t want to deal with the fumes, so I used home-made cornstarch paste (without the vinegar), which really adds a lot of moisture.

I tried to fix the wrinkling problem by ironing the poster board pieces dry. This worked pretty well, except blisters developed between the layers that make up the poster board. I had to pop the blisters with a pin and try to iron them flat. At this point, I really didn’t want to re-print all those pages and tape them together again, so I made a decision to forge ahead.

It went together fairly well after that. I stuffed the form with crumpled paper to help it keep its shape, and I put a couple of small bags of sand in the bottom to keep it from being top heavy. After it was assembled, I covered it with a layer of gummed kraft paper tape rather than paper mache, because paper tape holds less moisture and I was still having problems with the poster board warping when it got wet. I was running low on paper tape, so after that I switched to paper mache, using butcher paper and cornstarch paper mache paste, considering that I’m gluten intolerant.

I wish I’d thought to cover the form with plastic box sealing tape before adding layers of kraft paper tape or paper mache. That would have kept a lot of of the moisture out of the poster board. Why do I get all of these good ideas after the project is done?

After the first two layers of paper mache were dry, I used a razor knife to slice off the pointy dart ends, then rounded out the shape as best as I could with lightweight spackling compound before adding three a lot more layers of paper mache. If I’d stuck to using kraft paper tape, I think a total of three layers of tape would have been plenty, which would have saved a lot of time. I don’t think cornstarch paste dries as stiff as white flour paste, so you probably wouldn’t need as lots of layers of paper mache if you use flour paste, either.

After the paper mache was dry, I sprayed acrylic sealer on the form to preserve it.

It took me a weekend to assemble the dress form, then many hours over several days to add layers of paper mache. Seriously, I refuse to count how lots of hours I spent putting paper mache on this thing.

So yes, it is possible to use this pattern to make a full scale dress form. It would work fine as a display item, but it doesn’t quite have a sensible body shape, so I wouldn’t recommend using it for fitting purposes unless you pad it out to match your own body shape.

Share this:



Like this:
Like Loading…


Doll house size dress FormSomeone asked me if my miniature dress form patterns could be used to make 1:12 scale dress forms for a doll house. I was going to reply no, considering that they are created for quarter scale to half scale. but then I wondered if maybe the paper version could be made…
February 4, 2019In “Half-Scale Patternmaking and Sewing”

More complimentary Printable French curves + Hip CurvesIf you’re trying to find printable French curves or hip curves with measurement marks, here you go. I made both imperial (inches) and metric (centimeters) curves. The inch/centimeter marks are not numbered, so you can decide where you want to start numbering and add the numbers yourself. The pdfs have multiple…
October 19, 2014In “Patternmaking”

Creating Tiled PDFs in InkscapeDo you want to make professional looking print-at-home PDF patterns? how about doing it with complimentary software? There are lots of ways to create a tiled PDF pattern. Here’s how I do it in Inkscape, which is a complimentary vector graphics program. I wrote another post on getting started with Inkscape, so…
April 3, 2015In “Inkscape”

Author: liotv

Leave a Reply

Your email address will not be published. Required fields are marked *